On the other hand, getting a snow foam wash from the car wash every day can be exhausting and expensive. However, if you can figure out how to produce snow foam vehicle wash, you'll be in good shape. Then you can make your car wash at home instead of going to the car wash every time you need to clean the car.
Many people avoid going to the car wash because it is a nuisance. Additionally, car washes use automated equipment that has no will of its own and can cause problems instead of providing proper assistance.
If you are one of those people, keep reading. we'll show you how to make a snow foam car wash!
Why should you create a snow foam car wash?
But first, what exactly is snow foam? Is it possible to use snow foam as a car shampoo? Snow foam gets its name because it looks like a new blanket of snow on your car.
Snow foam, unlike hard ones, cleans your car. Even so, the majority of snow foam products are not vehicle shampoos. Instead, snow foam is a vital pre-wash that improves the performance of your car wash and extends the life of your paint.
The effectiveness of snow foam as a prewash is due to its consistency and chemistry, which make it preferable to a simple water rinse. In addition, snow foam will stay on your car longer than ordinary water, which will drain quickly. Finally, for optimal performance, snow foam adheres to vertical and lower surfaces.
Pollen in a wash mitt destroys a car's paint on a small scale, causing swirls and scratches. Snow Foam removes debris and floats it without rubbing it into the finish as a prewash. Road dirt, grime, sand and pollen are trapped by snow foam cleaners, which remove them from the surface of your vehicle.
Advanced hydrophobic polymers provide a streak-free rinse as snow foam suspends dirt from your car and flows. For example, Turtle Wax is pH balanced, meaning it won't strip wax or damage paint, clear coat, chrome, aluminum, plastic or rubber.
Spraying snow foam on your car using a snow foam cannon or foam gun attached to a pressure washer is the ideal method to take advantage of its pre-wash properties. This prevents scratches and swirls by ensuring there is no direct contact with the vehicle surface. If you don't have access to a pressure washer, you can still use a microfiber wash mitt and a gentle touch to take advantage of some of the pre-wash properties of the snow foam.
How To Make Snow Foam Car Wash – Making Snow Foam for Car Cleaning at Home
- A bucket of hot water
- a quarter cup of baking soda (Some prefer white vinegar)
- a quarter cup of dish soap (Some prefer to use baby shampoo, Adult fabric softener)
Grab a bucket to create car wash soap. You can usually pick one up for a dollar at your local grocery store or order one from Amazon.
Fill the bucket halfway with water after adding the dishwashing liquid and baking soda. It will start to look like a great car wash soap as the bucket fills up. (Either cold or hot water will do.)
Snow foam, unlike conventional detergents, cannot be sprayed onto a vehicle using a bucket and sponge. Instead, it should be administered with a pressure washer and a "snow foam lance" or "snow foam cannon".
The lance is a specially designed nozzle that attaches to your washer and pulls the liquid snow foam into the water stream, where it is then forced through a mesh that shakes the liquid snow foam into the thick foam that adheres to the car. To make the necessary foam, simply mix some snow foam liquid with water in the container of the snow foam gun and adjust the nozzle to adjust the amounts of water and air mixed.
Because different pressure washers and snow foam liquid compositions can vary, it may take some "trial and error" to achieve the exact, proper balance of snow foam and water.
Things worth looking out for before pressure washing Cars with snow foam car wash
This is an essential step that many people overlook: combine the snow foam liquid with some warm water inside the container of your lance. For example, if you usePro-Snow Kleen's Foam and Lance, mix one part snow foam with three parts water. This process will allow the foaming ingredients to activate properly before being sprayed through the snow foam lance. However, do not add too much water, as the foam can become too diluted.
The strength of the fluid is one thing to keep in mind. However, some solutions are generally safe and can remove seals and wax from your car.
Therefore, you should choose the one that states and comes with a more pH-balanced ingredient. Consequently, you don't have to worry about losing color when washing.
You can also follow our previous tutorial on how to make liquid snow foam.
Buy a high quality foam gun
After that, you will need an unusual item from the mall, namely a snow foam gun. But, again, since you might be a beginner, it is better to choose one that is not too difficult and comes with proper installation for easy use.
Also check and analyze the foaming capabilities of the device.
Many pressure washers include a foam cannon as an afterthought rather than an afterthought. As a result, they usually don't work well enough to produce the right consistency of snow foam for thorough car cleaning. Instead, consider purchasing a custom-made snow foam cannon.
Buy a pressure washer
ONEhigh quality pressure washeris a next item on the list. The key items that will play the most critical role in the operation are the pressure washers. We recommend a pressure washer with a pressure range of 1800 to 3000 PSI for the most power. Make sure the washing machine can also generate 8 liters per minute.
You will also need an 8-10 meter hose so you can have a relaxing wash without having to carry the machine around with you.
After completing the above requirements, you can attach the snow cannon to the machine and go!
Correct mixing method
Snow foam and water should be mixed in a ratio of 1:10, according to most experts. However, not all car snow foam contains the same ingredients. As a result, it is essential to follow the manufacturer's recommendations.
Typically, the foam should be thick enough to adhere to the surface of the vehicle. But, at the same time, it should not be so thick that it is difficult to wash off.
When the snow foam is too thick, it cannot be cleaned properly. In the end, the snow foam will just sit on the dirt of your car. A higher dilution ratio has the same effect. You will ruin the cleaning process if you use light snow foam.
conclusion
Well, our detailed tutorial showed you how to make snow foam car wash. For improved performance, use high quality snow foam fluids and follow our recommended fluid preparation recipe.
Your car is more than just a mode of transportation. They are much more than that, and as our constant companion, we have good reason to sympathize with them. Therefore, regularly provide the necessary maintenance to ensure a pleasant trip home every night!
We hope reading the blog made you feel a lot better. And you have learned more about how to make snow foam car wash at home.
Further reading
(3 Easier Ways) How to Make Car Wash Soap for a Pressure Washer
Rate this post
FAQs
Can you make your own snow foam? ›
To get started snow foaming your car, you'll need a bottle of snow foam car wash soap. The snow foam car wash soap will be mixed with water, then applied using a special snow foam cannon that mixes the soap/water mixture with air to create thick foam.
Can you use snow foam with a pressure washer? ›The best way to take advantage of snow foam's pre-wash capabilities is to spray it onto your vehicle with a snow foam cannon or foam gun connected to a pressure washer. This ensures no physical contact with the vehicle surface, preventing scratches and swirls.
What is the mix ratio for snow foam? ›You should use a (roughly) 3:1 mix of water and Snow Foam, with three parts of water for every one part of foam liquid. The exact quantities can vary, as the thickness of the foam can be affected by the settings of your lance as well as water hardness.
What is best pressure for snow foam? ›The majority of snow foams come in a concentrated formula, which requires diluting with water. This allows the pressure washer to create a thick foam, which lifts the dirt away. For best results, a pressure washer rated between 125- 220 bar should be used.
What are the ingredients in snow foam? ›| Sodium olefin sulfonate | 068439-57-6 | 931-534-0 |
|---|---|---|
| (C10-C16) Alcohol ethoxylate, sulfated, sodium salt | 068585-34-2 | 500-223-8 |
| Sodium chloride | 007647-14-5 | 231-598-3 |
Step 2 - Rinse the car
We always recommend spraying snow foam onto a wet car. This way you can get most of the top layer of dirt off the car before the foaming starts. So fire up the pressure washer and give your motor a quick rinsing down.
Unlike a car shampoo, snow foam doesn't contain any lubricant to help cloths glide over your car's surface, so wiping it off can cause scratches on your paintwork. Always rinse off your snow foam with a hose or a pressure washer.
How long do you leave snow foam on car? ›Spray the Snow Foam directly on to the vehicle without pre-rinsing it – Snow Foam works best when used on a dry surface. Spray it all over the vehicle bodywork and allow it to dwell for about 3-4 minutes – you will see the foam start to change colour as the dirt is lifted away from the surface of the paintwork.
Can you use any soap for snow foam? ›Any car shampoo works, but seek out the proper stuff
“A proper snow foam formula will be design to cling to the car and work much better than a shampoo,” Lee explains, adding, “The chemicals need to be strong in order to soften and decompose the oils/bugs/general road grime”.
Making your snow foam car wash at home is easy. Prepare a bucket with warm water, baking soda, and dishwashing soap. Mix them, and there you have your DIY snow foam. Purchase a high-quality pressure washer and foam gun for the best result.
Why is my snow foam not very foamy? ›
If it's too far away from your water source, or if your water source isn't putting out water at a high enough pressure, your washer will have a hard time generating the water pressure needed for thick snow foam. If the pressure isn't high enough, your snow foam won't be agitated into that thick, clingy foam.
What chemicals make fake snow? ›Artificial snow is made of a polyacrylate polymer, such as sodium polyacrylate, which is shredded to produce flakes of a similar size and colour to real snow. Sodium polyacrylate is a superabsorbent polymer, also known as a hydrogel, and can absorb up to 800 times its own weight in water.
How do you use Epsom salt for fake snow? ›Mix equal parts of the Epsom salts and warm water together in a cup, about half a cup of each will work well. Stir until most of the Epsom salts have dissolved. Add a few drops of food coloring and mix well. Then, use the mixture to paint a snowflake design on the paper.
How much PSI do you need for a foam cannon? ›A pressure washer with sufficient volume and pressure – Foam cannons generally require a minimum of 1100 PSI and 1.5 GPM output, though higher quality and performance foam cannons will usually require 1500 PSI minimum with 2 GPM output, typically the maximum PSI will be around 5000 PSI and 5 GPM but this can vary ...
What is the best mixture for a foam cannon? ›Although soaps aren't incredibly expensive, you can really burn through it fast when using a cannon. I like to mix with hot water for better foam but have found out that filling the whole bottle at a 10:1 ratio is actually twice what I need to spray my car.
Can any car shampoo be used as snow foam? ›Any car shampoo works, but seek out the proper stuff
“A proper snow foam formula will be design to cling to the car and work much better than a shampoo,” Lee explains, adding, “The chemicals need to be strong in order to soften and decompose the oils/bugs/general road grime”.
- Large Bucket.
- 3 gallons of distilled water.
- 8 ounces of bubble bath.
- 8 ounces of rubbing alcohol.
We always recommend spraying snow foam onto a wet car. This way you can get most of the top layer of dirt off the car before the foaming starts. So fire up the pressure washer and give your motor a quick rinsing down.